News

Screw press dehydrator product introduction

time:2023-07-17 14:34:39hit:101

Screw press dehydrator

Technical features of screw press dehydrator:


1. The screw press dehydrator has its own booster in the screw, which can realize the integrated crushing and pressing machine, saving space and saving equipment investment funds;


2. The spiral adopts a special structure forced feeding plate, and installs spiral leaf equipment to complete material transportation smoothly and extract dry humidity symmetrically;


3. The thrust of the extruding dehydrator to adjust the front and rear movement of the dry and wet tail vertebra can be a hand wheel, and the hydraulic control is selected, the operation state is stable, and the extruding and dehydrating operation is simple;


4. After gradual extraction, the dehydration is more thorough;


5. There is a mixer in the spiral of the screw extrusion dehydrator, which is more suitable for materials that need to be stirred;


6. Our company's screw extrusion dehydrator can realize the extrusion of internal steam, hot water, solvent, alcohol, etc.;


7. The screen of the spiral dehydrator has two sieves, and also has an overall structure, which is easy to disassemble and clean, and there is also a design of reinforced sieve bucket;


8. Realize the separation of "free water" in the material, improve the extraction speed, juice yield and dehydration rate;


9. Two presses can be connected in series, the front is used as a rough press, and then the second press is performed;


10. The screw is selected with precise size and accuracy, so that the screen of the press has a self-cleaning function and is not easy to be blocked;


11. German transmission technology, high torque, low noise, no vibration, less driving parts, less wearing parts, and low maintenance cost;


12. Stainless steel trapezoidal filter screen is used, which is wear-resistant, corrosion-resistant, durable and has good filtration performance;


13. The spiral adopts double-leaf split-push type, with fast extraction speed and small return flow;


14. The screw press dehydrator adopts a spiral design method of (kind of) material.




The use and maintenance of screw press dehydrator products:


1. Before use, clean the contact parts of equipment and materials with cleaning solution;


2. When it needs to be closed at the end of the extraction work, do not stop the operation of the equipment directly. Firstly, reduce the pressure of the hydraulic system to make the material residue after extraction and dehydration push open the forced door at the end of the sieve barrel; or manually lift the forced door, and then let the machine continue to run for a period of time until the material residue in the sieve barrel can no longer be discharged Press the door, then close it, and clean up the remaining material residue in the sieve bucket;


3. During the operation of the machine, try to avoid excessive pressure, otherwise it will cause failures such as sudden stop of the machine or rupture of the sieve bucket;


4. The oil temperature of the hydraulic system shall not exceed 60°C. Due to the fast pressure of the hydraulic pump, it is recommended that the continuous operation of the oil pump pressure should not exceed 30 minutes. The temperature rise of each bearing in the transmission device shall not exceed room temperature by 40°C;


5. During the operation of the machine, do not let sharp, hard objects and metal objects enter the machine body. They will damage the parts in the body and affect the normal operation of the machine. They can be selected before extracting materials;


6. If the machine is not used for a long time, all material residues in the machine body must be cleaned with a water gun, and the rust-prone parts are coated with grease for protection, and placed in a ventilated and dry place;


7. The oil in the hydraulic system should be kept clean. When refueling or changing the oil, the oil should be filtered with a 120-mesh filter;


8. The bearings of the transmission device should be regularly injected with lubricating grease for maintenance, the gearbox should be regularly injected with lubricating oil for maintenance, and the hydraulic oil tank should be regularly injected with hydraulic oil for maintenance.






If your company wants to establish a business relationship with us, please briefly describe the cooperation intention and send an email to:chuantaiscrewpress@gmail.com

17

Jul
2023