News

Screw press manufacturer direct sales

time:2023-08-08 14:58:35hit:110

screw press

screw press

Product advantages of screw press manufacturers:


1. Effectively improve the extrusion efficiency, and the contact surface with the material is small;


2. No blockage during use, and the equipment design is reasonable;


3. Stainless steel profile, good durability, wear resistance, long service life;


4. The screw press is an energy-saving product, which is directly driven by shaft mounting, stable and reliable operation, and relatively low energy consumption;


5. Place the spring partition in the spring partition to increase the dehydration effect and make the book support effect close to the ideal value;


6. The discharge port adopts a sealed design, which does not protect the production, does not pollute the surrounding environment, and keeps the environment clean and hygienic.


The working principle of the screw press manufacturer's equipment:


1. The liquid between various materials is discharged through the medium through the extrusion produced by variable diameter and screw pitch rotation, which has the advantages of high liquid extraction rate, small loss, small damage degree, and simple operation.


2. The material enters the machine from the feed port and is pushed forward through the screw. Since the main shaft of the spiral blade adopts the design method of unequal diameter and indefinite distance, the distance between the spiral blades from the feed port to the discharge port becomes smaller and smaller, so that The volume of the material in the stainless steel sieve frame is gradually compressed, so that the liquid between the materials is discharged through the sieve, and the liquid is continuously dehydrated from the material.


3. The filter device is composed of a screen frame, a screen frame cover and a stainless steel filter plate, and the bolts are fixed on the seat to support the normal dehydration of the screen plate during the extrusion process. The screen frame is welded with the stainless steel sieve plate, and the aperture diameter of the sieve plate is 0.2-2.5mm.


4. The conveying screw pushes the material entering the material box to the extrusion screw. By reducing the pitch of the extrusion screw and increasing the shaft diameter, the liquid contained in the material is squeezed out under the action of the resistance of the screen wall and the cone. The extruded liquid flows out from the mesh and collects in the collecting tank. The extruded dry solids are discharged through the discharge machine between the end of the screen cylinder and the resistance device.


The rear of the discharge port is equipped with a cylinder automatic resistance device. By adjusting the pre-tightening force and position, the discharge resistance and the size of the discharge port can be changed, and the dry humidity of the dehydrated discharge can be adjusted (adjust according to the actual use of the user).


Features of screw press machine:


1. Low cost of use


The screw press adopts the principle of physical extrusion dehydration, no additional heat source is required in the dehydration process, and the energy consumption is extremely low compared with similar drying equipment.


2. Large amount of continuous work processing


The parameter value of the screw auger is calculated and analyzed by mechanical means, and the axial thrust is increased by special technology, so as to ensure that the deviation, bridge, return material, shaft or other reasons cannot work continuously, and the processing capacity per unit time is greatly increased.


3. Low moisture in slag discharge


Due to the wide variety of materials to be dehydrated, different materials have different data such as water content, molecular water ratio, viscosity, fiber content, water absorption, toughness, organic or inorganic substances. Our engineers will analyze the material to be dehydrated provided by each customer, calculate the parameters suitable for the material, make suitable equipment, make full use of physical pressing, and reduce the water content of the extruded material.


4. Wear-resistant and corrosion-resistant


The key parts of the screw press are painted with a wear-resistant layer, and the surface of the screw auger blade is welded with a layer of alloy cutter head to increase wear resistance; the key parts are made of 304 stainless steel, which is acid-resistant, alkali-resistant, and corrosion-resistant, which greatly improves the service life of the equipment.


5. No need to add drugs


According to the characteristics of the material to be dehydrated, the screen with a gap of 0.3mm-1.0mm does not need to add coagulant and other drugs during the dehydration process, so there is no need to increase the cost, and the secondary utilization of the material will not be affected by the increase of the chemical composition. Influence.






If your company wants to establish a business relationship with us, please briefly describe the cooperation intention and send an email to:chuantaiscrewpress@gmail.com

08

Aug
2023